Then, with the starter key in contact position, actuate all pilot controls joysticks and pedals into both directions to relieve the servo pressure and back pressure in the working circuits, then relieve the tank pressure in the hydraulic tank by slowly turning the bleeder screw. Check the machine for paint damage and remedy, if necessary. Hold the attachment as close as possible to the loading platform. Be certain that all defects are taken care of immediately. Move very slowly and carefully towards the ramp and the transporting vehicle. Do not disconnect any lines or hoses or remove fittings, caps or covers before the attachment has been placed down and the engine has been turned off.
Bring all operating levers and controls into neutral position, place the safety lever up and turn the engine off, as outlined in the Operating Manual, before you leave the operator's seat. During off loading, use the same care and caution as during the loading procedure. After 5 minutes, carefully engage the travel hydraulic as well. Any risk in improperly using this machine is the responsibility of the user. Some illustrations in these operating instructions may depict details and working devices which differ to your machine. Always secure the raised cab with the safety bar before working under the raised cab! Always wear proper and safe work clothing. The safety lever must remain in the fully raised position! In some illustrations, protective devices and covers have been removed in the interests of better presentation.
Proper and destined use With the standard dozer attachment, the machine may only be used to loosen, move and dump dirt, gravel, broken rocks, or other similar material. At or near operating temperature, the engine cooling system is hot and under pressure. Procedure: - Remove all chains, wedges and blocks. Actuate all functions of the travel, working hydraulic as well as functions of additionally installed hydraulic components and alternately operate them over a period of approx. When tilting the cab, make sure that there is no one within the danger zone! Remove the cover carefully and slowly to relieve pressure. Always turn on the light if visibility is poor or as dusk approaches.
Secure all loose parts on the machine. Securely close all doors, covers and hoods on the machine. Warn all personnel in the surrounding area on the job site before operating the machine. Decals on the machine Several safety decals are attached on the machine. Always adapt the travel speed to the working conditions. Fresh water guidelines: To mix coolant fluid, use clean, clear water, which is not too hard.
Extend and retract the hydraulic cylinders fully for short periods. The Diesel fuel part may never be more than 50%. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Then add enough fuel to the fuel tank until it is full. Before starting the engine, warn any personnel in the surrounding area by sounding the horn.
Service, including maintenance, inspection and repair work Transport or loading the machine. Do not mix up the connections. Before putting the machine back into service, check all oil levels and correct them, if necessary. Using hoses and lines close to the limit ranges of permitted use can shorten the service life for example at high temperatures, frequent working cycles, extremely high impulse frequencies, multi-shift or around the clock operation. Procedure: - To lift spare parts and component assemblies for replacement on the machine, they must be securely mounted and secured onto the lifting devices, to prevent accidents. When replacing or changing any part of the attachment, such as blade, cutting edges, teeth,.
Before accessing the hydraulic circuit, with the engine turned off and the starter key in contact position, actuate all pilot controls joysticks and pedals in both directions to relieve the servo pressure and back pressures in the working circuits. Avoid any working movements, which could cause the machine to tip or slide or slip on a grade. Be certain that all clamps, guards and heat shields are installed. However, we recommend the use of these new oils, since the service life of the engine can be extended significantly by using these higher quality oils. Then start the Diesel engine and let it run for some time to bring the winter fuel into the fuel circuit.
Always enter and leave the cab through the left door. Allow only trained and authorized personnel to operate the machine, to maintain, service or repair it. In difficult circumstances, such as repeated cold start, higher sulfur content above 05. However, the 500 hour interval may not be exceeded. When performing a Delivery Inspection on a machine, the operator s must be trained using a current Operation Manual. If freezing temperatures are expected for the intended duration of shut down, then the fuel tank must be filled with winter fuel.
Match the machine speed to the travel route, to reduce vibration exposure: - Decrease the speed when driving on pathless terrain. For certain jobs, in addition to hard hats and safety shoes, additional safety equipment is required, such as safety glasses and gloves. Align the machine with the ramp. Move the machine slowly and carefully into an open area and check the travel and brake functions, the steering function as well as the turn signals and lights. Do not use Super gasoline for mixing.