Cab marker lights without the sunvisor option are standard bulbs see Bulb Replace- ment List in this manual. Install front cover by 44 ± 7 in-lb installing torx bolts. With the Volvo or for the fog lights and the electric heated side mirrors. For this reason, the rear hazard and tail lamps function differently than the tractor front and trailer rear signals. There are several variants of instruments, depending on what options have been The graphic display is in the lower left-hand side of the installed on the vehicle, and on whether the speedometer instrument cluster. For example, the switch controlling. W3000656 Push switch out of the panel.
A sensor or sender sends a signal to a control unit, or to the microprocessor in the instrument cluster. The central locking can be activated from either the passenger or driver side door lock. W3000652 Mount the wiper switch to the column 5 ± 0. Ignition Switch Connector Detail The ignition switch is mounted in the key lock assembly. The two circuits above and below each other are in parallel since there are two current paths. Insert the wire through the hole in the Push the contact out from the horn steering wheel where the old contact button area.
When replacing wires use onto the wire. It refers to a circuit that is completed in the wrong way, such as two bare wires touching each other, so that the current bypasses part of the normal circuit. Connect the terminal connectors and install the knob. It is a single switch of a new double contact design —. Torque bolts to 5 ± 0. Wire I feeds cab main power stud 1, and 1-A feeds. W3000698 Disconnect the clock electrical connector.
If the main supply is activated with one door locked and one unlocked, both sides will be automatically unlocked to prevent the driver being accidentally locked out. Voltage measured in volts is the force or pressure which pushes the current through the conductor. Pull the steering wheel from the steering shaft. Pull steering column back and up, 5 ± 0. When the tool is inserted, push on the switch to clear the switch tabs from the clips.
Remove bolts from rear column cover and remove cover. Install front 44 ± 7 in-lb cover by installing torx bolts and at- taching rubber grommets at stalk switches. They may be used on accessory and ignition circuits only. The windshield wiper module and central door lock module are covered later in this manual. W3000812 Use a rag and a pair of pliers to remove the rheostat knob. No part of this publication may be reproduced, stored in retrieval system, or transmitted in any forms by any means, electronic, me- chanical, photocopying, recording or otherwise, without the prior written permission of Volvo Trucks North America, Inc.
This can Anti-static wrist strap and mat damage sensitive electrical devices. Adjust the steering column up and to- 5 ± 0. Push the switch into the panel the back of the switch at the top and until it locks. Remove Replacement the front steering column cover by re- moving the 3 torx bolts from the cover. Failure to repair the short circuit which caused the fusible link to melt will result in the new fusible link melting. Remove the 2 screws from ment the ashtray housing, and remove the housing.
W3001007 1 Spacers Remove 3 bolts from the fuse panel,. Push the linkage arm away from the area where the motor is bolted to the housing. Note that each of these wires contains a fusible link. When working at the anti-static workbench, always keep a wrist strap connected to the anti-static mat. . A multimeter such as a Fluke 87 is recommended for troubleshooting. W3000650 To release the switch panel, reach be- hind the panel and depress the top and bottom clips on the left side.
If it starts at the battery, it must return to the battery. W3000675 Lower Edge of Dash Nut at Radio Mounting Bracket. The circuit number is stamped into the insulation every 76 mm 3 in. In- stall the nut on the rheostat shaft. Disconnect the 2 terminal connectors. W3000650 To release the switch panel, reach be- hind the panel and depress the top and bottom clips on the left side.