If you click on an appliance then you can see under the picture the words replacements parts and instruction manual. Rinse thoroughly with fresh water. Inspect to make sure that the sight gauge is straight. Install the reservoir plug by putting a rubber washer over the threaded end of the plug and inserting it into the remaining hole in the reservoir. Remove cover only when needed to stir occasionally or when adding ingredients. Insert the brass tubing into the tube to prevent possible collapse of the tube. If the boiling chamber does not move freely, recheck all connections.
Many of your favorite recipes may be adapted to the West Bend To do so, use the following guide. Do not operate any appliance with a damaged cord or plug. Insert one end of the piece into the smaller hole in the nylon elbow and tighten. To begin the flow of water to the distiller, turn the wing counterclockwise. Discard the brass ferrule which is not needed for use with plastic tubing. Retirez le couvercle uniquement lorsque cela se révèle nécessaire afin de mélanger de temps à.
From inside the reservoir, tighten into place using a black plastic jam nut. The saddle valve is now in the closed position. Also checkout this tip as it will help you to find what you are looking for on the website. Initial Cleaning Do not immerse boiling chamber in water or other liquid for cleaning. After removing the distiller from the box, open the boiling chamber cover and remove all packing material. Turn reservoir over so that it stands open side up.
When connected to the cold water supply line, the water will automatically feed into the boiling chamber, and shut off when the proper water level is achieved. When you get to the West Bend website you will see that you can move across the top tabs and see the different appliances in the drop down menus. If additional tubing is needed, contact your distributor. Install the sight gauge faucet by placing one rubber washer onto the threaded end of the faucet and inserting the faucet through the mounting hole in the reservoir. Jan 21, 2011 Many people are buying and using West Bend Kitchen Appliances.
The rear of the distiller is enclosed for your safety and contains no user serviceable parts. Just like anything that gets used hard these appliances do break or accidents happen, which require you to look for parts to replace the broken pieces. . Evite retirar la tapa al cocinar con cocción lenta, ya que el tiempo de cocción aumentará debido a la pérdida de temperatura. Register a Free 1 month Trial Account.
Installing The Pre filter if used instead of A length of food-grade tubing and the required fittings have been packed with your distiller. Also checkout this tip as it will help you to find what you are looking for on the website. Install the reservoir plug by putting a rubber washer over the threaded end of the plug and inserting it into the remaining hole in the reservoir. Here's a copy of your owner's manual for your West Bend Coffee espresso maker, model 55129. West Bend Bread Maker Owners Manual can be very useful guide, and west bend bread maker owners manual play an important role in your products. This is a disinfecting procedure. The condensing fan and the heating element of the boiling chamber are also controlled automatically, resulting in worry-free operation.
The cord has a three prong plug which mates with a standard three prong grounded wall outlet. Install a plastic foot on the bottom of each leg. If you are using one of on the distiller feed water line, you can discard this carbon post filter. From inside the reservoir, place a second rubber washer onto the protruding threaded end and securely tighten in place using the black plastic jam nut. Avoid squeezing out rubber washer. Install the sight gauge faucet by placing one rubber washer onto the threaded end of the faucet and inserting the faucet through the mounting hole in the reservoir. If an adapter is used, be sure adapter wire and wall outlet are grounded.
Also checkout this tip as it will help you to find what you are looking for on the website. Do not over-tighten jam nuts. It should not be possible to remove the tubing unless the grey release collar is pushed into the quick disconnect. The West Bend Water Systems distiller is constructed of durable stainless steel. Note: if carbon post filter is not used, you can bend the carbon filter holding frame down towards the bottom of the storage tank to allow more clearance between the distiller float and the storage tank fittings. Take a few moments now to identify the parts of your distiller, reservoir and accessories.
Rinse thoroughly with fresh water. Do not attempt to reuse the old filter. Click on the words and you will then go directly to the replacements parts or the instruction manual. Also many people will loose or throw away their West Bend Manuals. Para ello, utilice la siguiente guía: Si la receta recomienda….
Position the sight gauge retaining ring over the sight gauge and hook it over the edge of the reservoir. If there is any doubt as to whether the outlet is properly grounded, check with a qualified electrician. The water level in the boiling chamber is controlled automatically. You will need an adjustable wrench and a flathead screwdriver to hook up the distiller to the water supply. Pull down firmly on float ball s located underneath the distiller base to fully extend rod s from their locked shipping position. Installing Boiling Chamber Your distiller has been shipped with the boiling chamber already in place.